snowman

Snow and Rainbows

Continuing to try and make some new things for the small, outdoor, masks required pop-up craft fair I signed up to do at 3 Matadors for December 5th.

First I needed some more snowballs for snowmen, as I used up all the ones I had on hand. Back to the old grinder so to speak. 🙂

Making snowballs – rough cut then grind down to round

Getting the “big” snowman ready for resin

Laying out all of my small projects to work on today

Before I start mixing my resin, I lay out all of my projects and needed supplies. Today was the second layer of resin on the holly suncatcher and all five coasters, though one will be a new coaster design and the other four will be sandollars in the sand. I like to elevate the larger projects like the snowman panel so I can reach any drips that happen. I sometimes tape the underside edge, but forgot this today.

After resin and decorating – ready to cure!

I’m trying out some new colors of mica for the rainbow projects. I think they will be really pretty!

Close up of the rainbows / snowman suncatchers and coaster

Now everything just needs to sit overnight to cure.

Multitasking

Yesterday the friends who will be the recipients of the big Frank Lloyd Wright window came over and we decided to do another layer of resin. I decided that I really needed to move it to the garage for the final layer so I could access all sides of the window, despite the space being more prone to dust / humidity. Luckily it is an unseasonably warm day and the temperature in the garage was 75, which is perfect for my resin (Envirotex Lite).

This took a bit of planning as I had to mix up a lot more resin than usual and keep my family out of the garage (next to impossible today for some reason). However, after pouring, spreading and using my heat gun to clear the resin, everything looks good so far. Hopefully we can move it into the mud room later in the evening so the temperature remains a bit more consistent while it continues to cure overnight. In the meantime, I had a few smaller projects in the works I wanted to continue / start. Unfortunately this included repairs on a holly suncatcher I made yesterday. I had covered it with some wax paper to keep dust out while it cured and the paper made contact with the resin and made a giant mess. I had to carve some lumps off of the suncatcher today when it was cured enough, reinsert it into the mold and sort of “top it off” with another layer of resin. We’ll see how good it looks tomorrow (hopefully). I don’t think it will look as good as it would have had it not needed the repair, but I can likely keep it to use at home.

After chipping off the bumps and reinserting in the mold, prior to repair layer of resin

So all in all, I poured a second layer on three beachy coasters, first layer on two more beachy coasters, repair layer on the holly suncatcher / ornament and the first layers on three snowman ornaments.

I finished this guy yesterday and he cured overnight. Measures approximately 6.5″ w x 9.5″ tall, stained glass on recycled window glass coated with resin and decorated with glass chips, ground stone, glass glitter and blue shell accents.

Today’s Little Projects

I’m on roll with the holiday ornaments. I only have four molds, though, so I can only make four every other day, and that’s if I actually don’t skip any days, which I do. So it’s not a high output production, but it is a labor of love. 🙂

I poured the second layer on the fourth “Holiday Confetti” coaster and the first layer on the other five pieces. In addition, I poured the resin and decorated a small (though big compared to the other items) Snowman panel.

The yellow on the glass is actually painters tape I applied to the underside of the glass to make cleanup a bit easier. I pour a small amount of resin over all of the stained glass, then spread a thin layer over the rest of the backer glass so I have a substrate for my decorations to adhere to. In this case, I used crushed stone for snow, clear glass chips and blue shell chips for sparkle and interest. I dusted a bit of fine glass glitter over the snowbank and bottom area as well, but I’m finding that the glitter doesn’t seem to show up very well / as I would hope.

I also popped out some finished products from yesterday’s time spent creating.

I used some of the fine glass glitter in the Cardinal and Snowman suncatchers / ornaments above and it didn’t turn out as I had hoped. The glitter is sort of cloudy instead of sparkly. It still looks ok, just not the way I expected it to look. It might be better on the surface of my non-mold resin projects, so I will keep experimenting.

Charleston Snowmen

Today I poured the second layer of resin on several small projects and then spent some time making several small snowmen. I am experimenting with some abstract red and green coasters too, though my son says his favorite is the holly leaf suncatcher. My current favorites are the little snowmen. This is as close as you can get to making snowmen here in Charleston, SC. It’s 80 degrees outside and it’s well into November!

To make the “snowballs” for their bodies, I use glass nippers to rough out a generally round shape, then I use my glass grinder to smooth the edges. My fingers are pretty sore after making so many snowmen in one day! After the “snowballs” are ready, I paint on their faces (on the tiny ones). I use glass for the detail on the faces of the larger snowmen. Since these tiny ones are destined to be in two sided ornaments, I painted both sides of their faces / buttons and the little birds that will perch on their stick arms.

I also cut some backer glass and glued the pieces of this “big” snowman in place. I will pour the resin and decorate it another day, after the mosaic adhesive has had a chance to fully cure. This piece will be table top sized as it’s slightly smaller than a standard sheet of paper.

Cheer!

Today’s little ‘cheer-full’ projects! Second or third layers poured on the beachy coasters, first layer on all the others. I got some new colors of mica and other types of flitter / glitter from meyer-imports this week and I can’t wait to try them all out!

White molds are coasters, aqua molds are suncatchers / ornaments

More Holiday Fun

Started a few more ornaments today, poured the second layer on one coaster and started the first layer of a few more coasters.

In the holiday mood!

2Stained glass cardinals with green mica coasters, set of 4

Suncatchers / ornaments are between 3-3.5″ across. Handmade suncatchers are $20 each. Handmande coasters with stained glass are $50 for the set. Contact me for delivery / shipping options.

Holiday Suncatchers

Poured the second layer of resin on four Cardinal coasters (one needs a third layer as I ran out of resin) and the first layer on some new holiday suncatchers / ornaments!

Also took some better photos of the past few weeks worth of ornaments, though I’m no photographer with my phone, ha!

Suncatchers and Ornaments

I have a few suncatchers / ornaments on hand for last minute holiday gifting. Drop me an email, message me on twitter or tag me on my facebook page (see social links down on the right) if you would like to see them. Rectangular ones cost $25 each and are generally between 6-7 inches tall (including hanger) and square ones cost $15 each and are generally around 4-4.5 inches tall (including hanger). I also have some coasters available. I’ll try to get some good photos of them this week.